Leading 10 usual forklift accidents ， forklift procedure need to pay attention to these issues ！.

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift cargo blocked the vehicle driver's view, and the individual ahead can not be located, causing a moving crash.
Instance 2: In order to preserve the equilibrium of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift motorist does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure should pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be safe prior to starting.
3. When the forklift begins with a load, the motorist ought to initially verify that the lots is steady and dependable.
4. The start needs to be slow and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or lorries nearby, the driving signal ought to be released initially. High-speed doglegs are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a particular safety distance from the vehicle in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be raised except when stacking or filling. .
8. The elevation of the lots have to not obstruct the vehicle driver's view. In special situations, when the product affects the forward vision, drive at a low speed when turning around.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to base on the fork to hold items and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever operate with ailments or hide them.

packing and unloading.
1. When fork-loading things, the distance between both forks ought to be adjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product ought to protest the shelf. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In special conditions, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When utilizing a fork to Stand-on Electric Pallet Stacker fork the goods, the fork needs to be as deep as possible under the lots, and it should be kept in mind that the fork tip must not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the Electric Forklift Truck for Warehouse load does not move in reverse. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and hit difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to utilize forks to raise employees to engage in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be checked, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the operation of the forklift, examine whether the pressure and temperature are normal.
5. After the forklift is running, the external leakage must likewise be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the automobile;.
2. When you experience someone before you during driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is greater than 10%, the automobile must be driven backwards when worsening;.
8. When the forklift workers carry the goods and progress, if they encounter big or heavy products and most likely to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll items.
7. It is not enabled to bring people to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Auto parking is not allowed under the list below conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the road, the contrary side of the area with the very same size as the obstacle should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844